Tashkent
EN
Menu Close

How to check water quality: methods

Water quality is checked in three stages: with your senses, with inexpensive home tests and in a laboratory. Here is what you can do in the kitchen today, what you can buy for little money, and when you cannot do without a lab report.

How to check water quality: methods

Three levels of testing: where to start

The question of water quality rarely comes out of nowhere. The taste has changed, a layer of scale has built up at the bottom of the kettle within a week, rust started coming out of the tap after renovation work, the family moved into a house with a borehole, and you want to understand what exactly is going into your glass. The good news is that testing breaks down into levels, and you can go through the first two on your own.

Safety and convenience are different questions

It is worth separating two different questions straight away. The first is whether the water is safe: whether it contains bacteria, nitrates or heavy metals. The second is whether it is convenient to live with and pleasant to drink: hardness, scale, a chlorine aftertaste, rusty streaks in the sink. Home methods mostly answer the second question and the laboratory the first, and there is no need to mix them up.

Senses, devices, laboratory

The first level is your senses. It costs nothing, takes a minute and weeds out gross deviations: cloudiness, smell, aftertaste, sediment. A good share of real complaints about water can be seen this way, and no lab report is needed for them.

The second level is home devices and tests. A pocket meter for dissolved salts and a set of test strips together cost about as much as lunch in a café, and they already show numbers: total mineralisation, hardness, residual chlorine, nitrates, acidity. That is enough to keep an eye on your water month after month and notice changes in time.

The third level is the laboratory. Only there can they detect microbes, heavy metals, petroleum products and dozens of compounds that have no taste, smell or colour. It is the only way to get a document rather than a guess.

The order of testing

The mistake is usually one of two: either people get stuck at the first level and judge their water by taste for years, or they pay straight away for an extended analysis without understanding which parameters they actually need. It is better to work from the bottom up: the question of how to check water quality is solved step by step, free checks first, then cheap ones, and only with a specific suspicion do you go to the laboratory.

  1. Pour water into a clean glass and check it against the light, by smell and by taste
  2. Run two or three simple experiments with what you have: a kettle, a mirror, soap
  3. Measure the dissolved salts with a pocket meter and go over the water with test strips
  4. Write the results down and repeat the measurement a week later: what matters is not the figure itself but how it changes
  5. If something falls outside the norm or the source is new, order a lab analysis for the parameters you need

Next, each step is covered separately: what exactly to look at, what to measure with, how not to be misled, and at what point home methods run out.

Taste, smell, colour and sediment: testing without a single device

Assessment by the senses is not a rough glance but a method with its own procedure. The rules here are simple and were worked out long before devices appeared: clean glassware, daylight, two samples, one cold and one warmed, and no hurry.

How to take a sample

Start by drawing the sample correctly. Run the water for two or three minutes if the tap has not been used for a while: the first portion carries everything the pipes have had time to release, and it tells you about the plumbing in the building, not about the source. Take a clear glass without a pattern, washed without detergent, and fill it with a thin stream so as not to whip up bubbles.

Clarity, smell and taste

Clarity is checked against the light, by a window, with a sheet of white paper behind the glass. Fresh tap water is often milky from air: leave the glass for a couple of minutes and the cloudiness will clear from the bottom up. If it stays, or sediment settles, the cause is no longer air. Letting the water stand for three hours shows more: a reddish ring on the sides points to iron, a grey powder at the bottom to suspended matter, a film on the surface to organic matter or petroleum products.

Smell is checked twice: with cold water and with water warmed to about body temperature. Warmth brings out volatile substances, and what you could not smell in a glass straight from the tap comes through clearly once it is warmed. Chlorine is recognised at once, and a small amount is normal for a city supply. A rotten-egg smell points to hydrogen sulphide, an earthy or musty one to organic matter and bacteria in a system where water has been standing, and a medicinal or petrol smell to outside contamination; in that case the water must not be drunk until the cause is found.

Taste is only tested on water that is in principle fit to drink: tap water, bottled water, water from a source you know. An unfamiliar well or borehole is not tested by taste. A metallic aftertaste most often comes from iron, an astringent one from an excess of hardness salts, a salty one from chlorides and a bitter one from magnesium and sulphates. A flat, cottony taste says the opposite: there are almost no salts in the water. These four checks, colour, sediment, smell and taste, are exactly where people start when they wonder how to check the quality of their drinking water at home.

Clues from the plumbing

The plumbing tells you a lot too. A hard white deposit on the mixer tap and in the kettle means calcium and magnesium salts. Reddish streaks in the sink mean iron. Black specks in the shower head mean manganese. A slimy film on the aerator mesh or in the cistern is biofilm, and that is the least pleasant of the signs listed.

What the look, smell and taste of water tell you
SignLikely causeWhat to do next
Cloudiness that does not clear in ten minutesSuspended matter, clay, silt, pipe corrosion productsA mechanical filter at the inlet; letting it stand will not help
A reddish tint and rusty sedimentIron, old steel pipesMeasure iron with a strip, then fit iron removal
A strong smell of chlorineA lot of reagent in the network or a short distance from the treatment plantLet it stand in an open container, fit a carbon cartridge
A rotten-egg smellHydrogen sulphide, sulphate-reducing bacteriaLab analysis and disinfection of the source
An astringent taste and white depositCalcium and magnesium salts, high hardnessA hardness strip, and softening if it is confirmed
A medicinal or petrol smellOutside contamination of the sourceDo not drink it; urgent analysis for petroleum products and phenols

The limit of this method is obvious. The most dangerous things in water have no colour, smell or taste: nitrates, lead, cadmium, arsenic and most bacteria cannot be picked up by the senses at all. Clear, pleasant water may well turn out to be unfit to drink, and conversely, hard, bad-tasting water is often perfectly safe. Judging by eye screens out the obvious, but it does not confirm that water is fit to drink.

Home experiments: kettle, mirror, soap and tea

The next step is a few tests that need nothing but what you already have in the kitchen. Each checks one parameter and takes a few minutes, and together they give a fairly coherent picture of hardness, dissolved salts and iron.

Five kitchen experiments

  1. Kettle. Look at the bottom or the heating element a week after descaling. A thick white crust means high hardness, a thin deposit medium hardness, and clean metal soft water
  2. Mirror. Put a drop of water on clean glass and let it dry without wiping. White marks around the edge of the drop are dissolved salts, and the more visible the ring, the more of them there are
  3. Soap. Shake water with a piece of plain laundry soap in a closed jar. In soft water the lather rises quickly and lasts; in hard water there is hardly any lather, but grey flakes appear
  4. Tea. Brew strong black tea and dilute it with the water you are testing. A clear, light infusion is normal; cloudiness and a bluish-grey tint mean an excess of salts and iron
  5. Potassium permanganate. Dissolve a few crystals in a glass of water: a lasting pink colour is normal, while a quick change to yellow or brown indicates organic contamination

This is what an honest answer looks like to the question of how to check water quality at home with everyday items: five experiments, no cost, and an understanding of whether your water is soft or hard, whether it contains iron and how much organic matter there is. That is already enough to choose a filter.

Sediment after boiling

It is also worth boiling the water and looking at it once it has cooled. Flakes at the bottom after boiling are hardness salts that have settled out, and their amount makes it easy to compare two sources. Boil the same volume in the same pot and compare the sediment: the difference between tap water and water from a bottle is usually visible the first time.

All these tests are comparative, not absolute. Their strength is not that they give a number but that they let you put two samples side by side: tap water and bottled water, water before a filter and after it, water in your old flat and in your new one. It is the difference that is useful, not a single result on its own.

The limits of kitchen experiments

What kitchen experiments cannot do is tell harmless from dangerous. Scale damages appliances and taste, but not health. No scale does not mean clean water: distilled water leaves no sediment either, and drinking it all the time is not a good idea. None of the experiments listed will show nitrates, lead or E. coli, and you should not count on them to.

There are also frankly useless tests that often turn up in advice. The experiment with a battery and two nails, where the water turns cloudy and brown, shows not contamination but electrolysis of the iron electrodes themselves: you will get the same result with bottled water. A silver spoon left in a jar overnight disinfects nothing in household quantities. Shining a laser pointer through the water shows only suspended matter, which you can see without the pointer anyway.

Devices for little money: a salt meter and test strips

A pocket meter for total dissolved salts, usually called a TDS meter, costs about as much as a good lunch and lasts for years. It works indirectly: it measures the electrical conductivity of the water and converts it into milligrams of dissolved substances per litre. You dip the electrodes, wait a few seconds and see a number.

Three conditions for an accurate reading

It is simple to use, but there are three conditions. The sample must be at room temperature: warm water conducts better and inflates the reading. After a measurement the electrodes are rinsed and wiped dry, otherwise the next result inherits the previous one. And once a year the device is worth checking against a calibration solution, or at least against bottled water with the mineralisation stated on the label.

How to read a dissolved-salts meter
Reading, mg per litreHow to read itWhat usually lies behind it
up to 50Almost distilledReverse osmosis without a remineralising cartridge
50–150Soft, low mineralisationMelted and mountain water, some bottled water
150–400A comfortable range for everyday drinkingA good borehole, good-quality bottled water
400–700Noticeable hardnessThe city supply in many districts
700–1000High mineralisationYou need to find out which salts make it up
over 1000Beyond drinking-water limitsBetter not to drink it until a lab analysis

What the device cannot tell apart

The main limitation of the device is that it does not tell substances apart. Four hundred units may be calcium and magnesium, or they may be sodium and nitrates, and on the screen it will be the same number. A low reading does not mean clean water either: organic matter, bacteria and petroleum products barely conduct electricity and do not show up in this figure at all.

So the question of how to determine water quality at home is not settled by one device: the meter is good as a watchman, not as an expert. Its real work begins once you have written down the typical value for your tap and keep track of deviations from it.

Test strips

The second inexpensive tool is test strips. A strip with several coloured pads is dipped in water for a couple of seconds, and a minute later the colour is compared with the scale on the pack. Sets are available for total hardness, free chlorine, nitrates and nitrites, acidity and iron, and less often for copper and lead. They are sold in pharmacies, aquarium shops and household chemicals departments.

  • Check the expiry date: an expired reagent gives an understated result rather than failing to work
  • Keep the pack tightly closed and in the dark: strips are spoiled by moisture and light
  • Do not exceed the waiting time in the instructions: the colour keeps changing after the right moment
  • Compare the colour in daylight, not under a yellow kitchen lamp
  • Repeat the test with a second strip if the result falls on the border between two marks on the scale

The accuracy of strips is moderate: they answer in ranges, not numbers, and borderline values are hard to read. But they cover exactly what the salt meter cannot see: nitrates, chlorine and acidity. The meter and strips together cover almost everything you can find out about water in a kitchen.

A log of readings

Get into the habit of writing things down. After six months, a notebook or a note on your phone with the date, the source and the readings is worth more than any one-off analysis: it shows that hardness went up after the water intake was switched, that a cartridge stopped working a month before its stated life, that nitrates in the well jumped in spring.

Where home methods end: laboratory analysis

Home methods tell you about hardness, taste and overall dissolved salts, and that is where their abilities run out. Safety is determined by substances that nothing in a kitchen can reveal: they have no colour, smell or taste, and their effect on conductivity is too weak for a pocket device to notice.

Three groups of parameters

These are three groups of parameters. The first is microbiology: E. coli, enterococci, total microbial count. The second is toxic elements: lead, cadmium, arsenic, mercury, as well as excess iron, manganese and fluoride. The third is chemicals from human activity: nitrates and nitrites from fertilisers and cesspits, petroleum products, phenols, pesticides.

What is found most often in private wells and shallow boreholes is nitrates. Water containing them is clear, tastes pleasant and has no smell, yet it is dangerous above all for infants and pregnant women. This is where the line runs: if you ask how to check water purity at home in a way that gives you a guarantee, the honest answer is an unwelcome one: you cannot. A home strip will show an exceedance roughly, a laboratory will give the exact value, and the difference between them is fundamental.

Choosing a laboratory and taking a sample

A laboratory is chosen by its accreditation. The organisation must have a scope of accreditation that lists water parameters, and it must issue a test report, not a certificate in free form. Such laboratories operate at water utilities, sanitary services and large universities, and as private companies. They usually also provide or sell containers for the sample.

  1. Get a container from the laboratory or use a clean glass bottle; for microbiology only a sterile container issued by the laboratory will do
  2. Run the water for five to ten minutes so that you take water from the supply, not water that has been standing in the pipe
  3. For a microbiological sample, heat the tap spout with a lighter and do not touch the neck of the container with your hands
  4. Fill it with a thin stream right to the top so that no air bubble is left, and close it tightly
  5. Label it with the date, time and source, and deliver the sample within two or three hours, in a cool bag in hot weather

Which analysis to order

The set of parameters is chosen according to the source. For city water a short analysis is usually enough: hardness, iron, chlorides, sulphates, residual chlorine, turbidity and acidity. A borehole or a well needs an extended one, always including microbiology and nitrates. If there is an industrial zone, fields or a petrol station nearby, petroleum products and heavy metals are added.

What to order depending on the source
SourceParameters you must includeHow often
City mainsHardness, iron, chlorides, sulphates, residual chlorine, turbidityEvery two or three years and after accidents on the network
BoreholeFull salt composition, nitrates, iron, manganese, microbiologyBefore first use, then once a year
WellNitrates, microbiology, ammonium, oxidisabilityTwice a year, always in spring
Water after a filterThe same parameters that were exceeded before the filterRight after installation and once a year
Bottled waterThe producer's test report on requestOnce, when you change supplier

The cost grows with the list of parameters: a full analysis can cost several times more than a short one, and it takes from two working days to two weeks. It makes sense to find out the exact prices at a specific laboratory, as they vary noticeably even within one city.

How to read a test report

A separate subtlety is reading the report. It has three columns: the parameter, the value found and the permitted limit. What you should look at is not the frightening names of substances but the rows where the value found is above the limit, and by how much. Iron exceeding the limit by half is solved by choosing the right filter, while any exceedance in microbiology means the raw water must not be drunk until the cause is eliminated.

Filters and purified water: what they remove and what they take away

An analysis makes sense when a decision follows it. There are not many decisions available at home, and each deals with its own group of problems and leaves the rest untouched.

Five methods and their limits

Home purification methods and their limits
Purification methodWhat it deals withWhat it does not do
Jug with a carbon cartridgeChlorine, aftertaste, smell, some organic matterDoes not seriously reduce hardness or kill bacteria
Flow-through sorption filterChlorine, organic matter, solid particlesDoes not remove nitrates or dissolved salts
Ion-exchange softenerCalcium and magnesium salts, scaleReplaces them with sodium, does not touch microbiology
Reverse osmosisSalts, nitrates, heavy metals, most bacteriaTakes away useful minerals along with them
Ultraviolet disinfectionBacteria and virusesDoes not change the chemical composition at all

Reverse osmosis and minerals

Reverse osmosis is the most radical of the home methods. A semi-permeable membrane lets water molecules through and holds back almost everything else: hardness salts, nitrates, heavy metals, microorganisms. What comes out is very soft water with no scale and no odd aftertaste, good for both the kettle and the iron.

This is where a long-running argument begins, and it always sounds the same: purified water, benefit and harm. The membrane does not choose: along with lead and nitrates it removes calcium, magnesium and potassium. For someone who gets minerals from ordinary food the loss is insignificant; for someone with a monotonous diet it is more noticeable. A sensible compromise is a remineralising cartridge after the membrane: it gives the water back some of its salts and taste.

Cartridge life

The second point about purification is maintenance. A spent cartridge stops holding things back and starts releasing them: the organic matter it has collected becomes a breeding ground in a warm kitchen. A filter that has not been changed for a year more often makes water worse than better. That is why every system has a service life in litres and in months, and the one that usually runs out first is the one people forgot about.

  • Replace cartridges by whichever limit comes first: the volume filtered or the calendar
  • Rinse a new cartridge before first use as described in the instructions
  • Do not leave a jug of water in the sun or in the warmth for more than a day
  • Protect the osmosis membrane from solid particles: a pre-filter in front of it is essential
  • Once a year, have the water before and after the filter analysed: it is the only honest check of how it works

Boiling is not purification

And one more common misconception: boiling is not a filter. It kills bacteria and drives off volatile chlorine, but the hardness salts go nowhere, and the concentration of everything else even rises slightly, because some of the water evaporates. As a way to disinfect, boiling works; as a way to purify, it does not.

What to drink in the end: comparing sources

Once the results are in, all that remains is to choose a source for everyday drinking. In the city there are four options, and each has its own weak spot.

Strengths and weaknesses of the sources

  • Mains water is controlled where it leaves the treatment plant, but it picks up iron and microbes in the building's own old pipes
  • A borehole or a well does not depend on the network, but it is entirely the owner's responsibility and changes from season to season
  • Water after a home filter is predictable as long as the filter is maintained, and no better than the original once it is forgotten
  • Bottled water has a composition known in advance, but it depends on the producer's integrity and on the cleanliness of the containers

When people ask which water is healthiest, they usually expect the name of a single source. There is no such answer. There is a range: water free of microbes and toxic elements, with moderate mineralisation, roughly one hundred and fifty to four hundred milligrams of salts per litre, and acidity close to neutral. Which tap or which bottle it came from makes no difference to the body.

Mineral water by type

Mineral water deserves a separate word. Table water with low mineralisation can be drunk without restriction. Medicinal table water is drunk in courses, not instead of ordinary water. Medicinal water with high mineralisation is prescribed like a medicine and should not be drunk all the time. Confusing these three categories is the most common mistake in the shop, and what tells them apart is the wording on the label and the total mineralisation stated there too.

Checking bottled water

Bottled water can be checked too, and not only by taste. Part of the check is done right at the moment of purchase, the rest at home, with the same devices as for tap water.

  • Read the label: it must state the type of water, the source, the total mineralisation and the main salt composition
  • Compare the stated mineralisation with the reading of a pocket meter: a difference of several times does not inspire trust
  • Look at the container against the light: cloudiness, deep scratches and deposits inside mean the bottle has served its time
  • Smell the empty bottle once the water is finished: an odd smell points to poor sanitising
  • Ask for the test report: a conscientious producer has one and shows it at the first request

A yearly routine

Put everything said here together into a simple yearly routine. Once a week, a look at the water in a glass and at the deposit in the kettle. Once a month, a dissolved-salts reading and a strip for hardness and nitrates. Once a year, a lab analysis for the parameters of your source and a check of the filter before and after. This routine takes less than an hour a year and settles almost every question about the water your family drinks.

Read more: Artesian water

In short

  • Testing goes from the bottom up: first the senses, then inexpensive home tests, and the laboratory only with a specific suspicion.
  • Judging by look and taste, and kitchen experiments, catch hardness, iron and organic matter but say nothing about nitrates, metals and bacteria.
  • A pocket salt meter is useful as a watchman: it shows a deviation from the usual figure, not the composition of the water.
  • Only a report from an accredited laboratory gives a precise answer about safety, and the set of parameters is chosen according to the source.
  • A filter solves the problem the analysis revealed, and works only until the cartridge is due for replacement.

FAQ

Can you judge water quality by taste and smell?

Partly. That way you can notice chlorine, iron, hydrogen sulphide, hardness and organic matter. Nitrates, lead and bacteria have neither taste nor smell, so water that tastes pleasant is not necessarily safe.

Do you need a dissolved-salts meter at home if you have a filter?

That is exactly what it is for: seeing how the filter is working. Write down the reading right after replacing the cartridge and keep an eye on it: when the figure returns to the original value, the cartridge's life is over.

How often should water be sent for analysis?

City mains: every two or three years and after accidents on the network. A borehole: once a year. A well: twice a year, always in spring, since floodwater brings nitrates and microbes.

Does boiling make water safe?

Boiling kills bacteria and drives off volatile chlorine, but it does not remove salts, nitrates or heavy metals. As water boils away their concentration even rises slightly, so it is best not to boil the same water twice.

What should I do if the analysis shows an exceedance?

Look at which parameter it is and by how many times it is exceeded. Iron and hardness are solved by choosing the right filter, nitrates by reverse osmosis, while an exceedance in microbiology means the raw water must not be drunk until the cause is eliminated.

Message us